Відео

15:38 “why did i do it again?” The most common question when fooling around with an engine 😂

Love to see the work finally pay off with the beast getting back to the job it was created for! Great work Sir!

I love this mower. Older machines have an aura that is completely missing in newer models. My 1954 Yazoo 60" mower was the first to be able to turn around its own front tyre axis with a single steering rear wheel and a transaxle with two wheels in front. It is a real beast and I love to use it once a week in our English-style park.

Your attention to detail is very nice

Great work as always. I really appreciate all the time and effort you put in to your videos. Thanks for sharing.

Why don't put PB blaster on the crank shaft 😊

The Question is old chap , would you restore the lawnmower if did not have a diecast Deck............

Had some bad experiences with those pulleys getting rusted to the spindles. Worst one was where the pulley and the spindle were of an odd size, so both _had_ to be saved. Cutting was out of the question, heat was not enough, and puller was starting to mess up the pulley. Ended up plugging up the grease port at the top, then welding on a steel cap with another grease zerk in it over the end (welded to the pulley). After everything cooled off that cap got pumped full of grease and finally enough pressure got built up that it forced the pulley off the shaft. Grease got re-used for actual grease-y purposes later, so no waste there.

I could take it apart but when I put it back together would have a bucket of nuts, bolts and parts left

Can you tell me why that sheet metal gets pounded up on those bolts on the muffler? Not the first time I’ve noticed this. Sorry for my ignorance!

I think it's cool how much less toxic these comments are to your other channel those other guys will complain about anything, Keep on keeping on dude

Dude your work is impeccably brilliant, love watching your videos, would rather wait for new videos instead of you sacrificing your quality for the algorithm 😊keep up the awesome work!!!!

Excellent job!

Amazing work I really liked the video

Have you worked on other small engine vehicles, like an old Honda Three wheeler or something similar?

Impressive restoration. Unlike those fake restorations where they spray dirt on and leave it in the jungle to be found. This video is legit.

That was the most epic fix I ever watched. Thanks for posting.

I'm in need of your prayers and positive energy. Please keep me in your thoughts.

After taking off the carrier plate, you will see @ 2m:59s, a square headed bolt. Provided one has easy access, that is the correct point of access to properly drain the oil sump. Once a year, I removed carrier plate to easily remove and replace lawn mowers blades. At the same time, I remove sump plug and drain oil out. By the time oil has completely drained out, I have already replaced the 4x lawn mower blades on carrier plate, then re-attached oil sump plug and then re-attach carrier plate. Mind you mine is a Briggs and Stratton, and would be completely different to this mower.

Very nice ,good job

Really like this style, where you give us a cost/profit breakdown at the end! I've always wondered how much you make on some of these and would love to see it in future videos.

why are you doing things backwards? loosen the belt tension spring, then pull the belt off and take the pulleys off, i dont understand the need to skip steps just because, you need to inspect that tension spring anyway for slack or if its too tight. which could be a reason as to why the belt itself was skuffed up on top, just as much as the pulleys could be out of alignment.

Very nice done

very good video

The British Sling Blade. I love this guy, keep going.

I wouldn’t let you work on any machinery. Your lack of mechanical knowledge is worrying. You see the 2 small holes in the pulley? You use those with the correct puller to remove the pulley.

Another fine job in the books. Great work as always!

Love the videos….word of advice, get rid of the flat steel rule when cutting using a knife and get yourself a metal safety rule (it has a “M” shaped profile). I sliced the end of my finger off when the knife slipped and ran across the metal rule.

May i suggest a AVAPOW 6,000 amp jump pack? I beleave amazon has it for $120 USD. I used to have the noco boost x gb45 1250a 12v jump pack but it kept overloading and i could only jump like maybe 2 cars b4 i had to charge it for 10 hours. The avapow so far for me is nice and lasts alot longer.

That came out very nice. I’ve never seen a rear discharge before.

Excellent Job Restoring Deck On Riding Mower

You do a very good job on these videos. Would really like to see if you have more to come of that blue quad. Thanks!

Hey dude, thanks so much for the effort you put into these videos. We love them so much. I almost jump for joy every time I see a new restoration video pop up. I know it's hard work, so just want you to know that it's appreciated. Love from New Jersey USA🤘

what a nice job on that deck. Seems to cut nice too.

Nice to see another video 👍 Turned out really well. I've started using 2K Raptor on the underside of the decks, it's really solid stuff!

You should see the lawnmower Honda hrb 475 (made in usa )i found at a farmers dump in the forest , 100 times worse than that and it had been there for 6 years ish. but i made it run today :) trash to treasure

Where I live at in the USA u don’t restore mower decks. It doesn’t make sense to have it done because the cost of labor always outweighs the cost of get a used deck. had 3 different people tell me that work on lawn tractors this. As long as it’s mechanical sound just use it as is if it has surface rust on it dont paint it

hi god bless you for good content keep up the good work

Great video. what was the rebuild cost versus the cost of a new deck ?

Great video as always ! Thinking about the under deck cleaning, i personnaly use a rotary pressure jet, i think it's more efficient than straight jet

Excellent work. Thank you for this great video.

I know few protectionist people. They drive me crazy 🤪. It's just a mower. 😊

Newbie’s question: why grease for the gearbox and not gearbox oil ?

Well done! The only thing I would have changed is the belt, then everything is new 😂

I’m from Michigan and I have never seen a garden tractor like that, looks pretty stout 💪🏻

Great video. As for the powdercoating, I'm not in favour of treating decks with this method. The reason being that powder doesn't creat chemical reaction with metal that would protect the rust. Also, when even smallest imperfection occurs while normal use, and nitrogen from grass starts its action, the coat peels off with plasters after short time. Just my opinion out of observation.

I have a 1980's Murray 11/36. im guessing 11hp 36 inch cut. Lovely old briggs motor that was all working 2 years ago. Just needs a new toothed head bit.. the part the starter motor spins whatever thats called. Anyway... used a makita 18v drill to start her up. 5 forward gears and 1 reverse. Though it does have the mountfield nose on it from a previous owner.

Always appreciate a great rebuild thanks so much for the video weirdly satisfying 😊

How and where do you get those sticker decals?

You should get a sponsor from WD-40